Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Fence Installation: The West Palm Beach Owner’s Guide
Mr-Glass fence installation in West Palm Beach typically runs $3,500 – $9,000 installed, depending on the panel run, post condition, and whether we’re working with framed glass or frameless channel-mounted sections. We stock Mr-Glass-compatible channel, posts, and hardware on our trucks, and we can usually match a failed panel or rail to the existing system within one site visit. What usually brings a homeowner to this page is a panel that’s started to rattle in the frame, a gate that no longer swings square, or a footing that’s lifted after a summer of afternoon storms.
Which Mr-Glass Models This Applies To
Mr-Glass has shifted its post and channel systems over the years, and the part that fits a 2012 install is not always the part that fits a 2020 build. The main split is between the early round-post framed system and the newer square-profile channel system that most West Palm Beach homes we see today were built with. If you have the original paperwork, the model code is printed on the inside face of the gate stile. If you don’t, we measure the channel throat width and glass thickness on site: most Mr-Glass panels in this market are 10mm or 12mm tempered, and the two are not interchangeable in the same channel.
For hardware, the hinge and latch are the parts worth matching to OEM. Aftermarket rollers for the gate track are fine in most cases, but the hinge barrel diameter is proprietary on some Mr-Glass lines and a generic hinge will leave the gate toeing in or out over time. We’re an independent service provider, not affiliated with Mr-Glass, and we’ll tell you plainly when an OEM part is the only sensible call and when a stock equivalent will do the same job for less.
Styles & brands we work with
Signs Your Mr-Glass Fence Installation Is Failing
- Panel rattle in the frame. The rubber gasket inside the channel has compressed or dried out from salt air and heat. The glass itself is usually fine; the channel needs re-bedding or the gasket replaced.
- Gate drags or binds at the latch side. The hinge post has moved, or the concrete footing has settled. In Flamingo Park and El Cid, we see older footings that weren’t poured deep enough for our soil, and the post starts walking.
- White haze or clouding along the glass edge. Water has been sitting in the channel. This is a drainage issue, not a glass defect, and it’s fixable by re-setting the channel with proper weep clearance.
- Rusted or stiff latch hardware. Coastal humidity in West Palm Beach is hard on plated steel. The latch is usually the first hardware piece to go, and it’s a quick, inexpensive swap if caught before the strike plate wears.
- Glass sits lower on one side of the panel. The setting block inside the channel has degraded. Left alone, the glass will eventually rest directly on the metal channel and you risk a stress crack at the corner.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In West Palm Beach, a full Mr-Glass fence installation typically falls between $3,500 and $9,000. A single panel re-set or gate hardware swap is far less, usually a few hundred dollars including the call-out. A full run of posts pulled and re-footed is at the higher end.
Here’s how the pricing breaks down for most projects:
- Single panel re-bed (gasket, setting blocks, drainage correction): $350 – $700
- Gate hinge and latch replacement (OEM-matched hardware): $400 – $900
- Post reset with new concrete footing: $600 – $1,400 per post
- Full fence installation, new channel and panels, standard lot: $3,500 – $9,000
Every quote is a written price before any work starts, line by line, so you know what the channel costs, what the glass costs, and what the labor costs. Graham Stein walks each site himself before we write it up. If the price changes after we open the footing and find something unexpected, we stop and show you exactly what we found before touching anything else.
Key takeaways: Most Mr-Glass failures in this climate are channel and footing issues, not glass failures. The glass itself rarely needs replacing. And a written price before work starts is the rule on every single job we take.
DIY or Call Us?
For a Mr-Glass fence system, most of what fails is not something we’d recommend a homeowner tackle. Tempered glass panels are heavy, a 10mm panel on a 36-inch gate section runs about 90 pounds, and when a setting block fails or a channel pops free, the panel can drop suddenly and without warning. We’ve had to re-cut a channel after a well-meaning homeowner removed a panel alone and chipped the corner against the pavers.
What you can safely do is identify the issue: note where the rattle is, check whether the gate hinge screws are loose, and look for standing water in the channel track. Then call us at (728) 203-3270. We’ll come out, measure, and give you a written price for the fix. If it’s a five-minute hardware adjustment, we’ll tell you that too and charge accordingly. Put it in writing, then do exactly that.
FAQs
The tempered glass panels themselves can last 20 years or more. What doesn’t survive West Palm Beach weather indefinitely is the metal: salt air eats the channel and post hardware, and afternoon storms stress the footings. Expect the glass to outlast the frame by a factor of two, and budget for hardware and channel service every 8 to 12 years. Call (728) 203-3270 and we’ll assess what’s actually aged on your fence versus what’s still solid.
Most panel failures are repairable, because the glass is usually fine and the parts around it are what failed. Re-bedding a panel with new gaskets and setting blocks costs a few hundred dollars and takes under two hours. We only replace glass when it’s cracked, deeply scratched, or has a stress fracture from sitting on the metal channel.
A single panel re-set is a half-day job. A full fence or a run of post resets is typically two to four days, depending on how many footings need concrete and curing time. We’ll give you a firm start and end window in writing before we begin, and we’ll work around nap hours and pet routines where we can.
We stock the channel, gaskets, setting blocks, and common hardware on our trucks, and we can source OEM Mr-Glass hinges and latches within a few days when a proprietary part is required. We also work with KraftMaid, Cambria, and Silestone for other brand-specific components.
If your Mr-Glass fence is rattling, binding, or sitting in water, call us at (728) 203-3270. We’ll come out, measure, and hand you a written price before any work starts. Same standard on every job, every time.
Written by Graham Stein, Owner, Elmstead Remodeling West Palm Beach at Elmstead Remodeling West Palm Beach, serving West Palm Beach and nearby areas.
