Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Kitchen Remodeling: The West Palm Beach Owner’s Guide
If you have a CWS kitchen and a component has failed, we stock the parts and do the install. A full CWS kitchen remodeling project in West Palm Beach typically runs $14,000 – $45,000 depending on scope, cabinet line, countertop material, and how much plumbing or electrical work the existing layout requires. Most single-part replacements, like a failed drawer glide, a warped cabinet door, or a cracked backsplash section, land well below that range. Here’s how owners usually discover the problem: a drawer that no longer soft-closes, a hinge that lets a door droop, a countertop seam that has opened, or a cabinet box that has pulled away from the wall after years of Florida humidity and daily use.
We are an independent West Palm Beach contractor, not a corporate branch of CWS. That matters because we work on the kitchen as it actually performs in this climate – salt air near the coast, humidity that swells wood and tests adhesives, and homes from Flamingo Park to El Cid where the original CWS install may be ten or fifteen years old. Graham Stein walks every job before a single tool comes off the truck, and you get a written scope of work before we start. Put it in writing, then do exactly that.
Which CWS Models This Applies To
CWS kitchen lines run across a few common configurations, and most parts are identified by a model label inside the cabinet box, under the drawer tray, or on the back of the door panel. Look for a printed sticker or etched code with the cabinet series and a date stamp. If the label is gone – and in West Palm Beach’s humidity, paper labels often are – take a photo of the drawer glide, the hinge pattern, and the door profile. That usually tells us what we need to know.
The bigger decision with CWS is OEM versus quality aftermarket. CWS soft-close hardware, for example, is built to a European 35mm hinge cup standard, so a door with a CWS label can often accept a Blum or Grass hinge without modification. Drawer glides are typically 18-inch or 21-inch full-extension units; the CWS versions hold up well, but the aftermarket equivalents we carry – name-brand units with the same weight rating and stroke length – cost less and carry their own manufacturer warranty. For cabinet doors, drawer fronts, and face frames, OEM or matched custom shop is the honest choice: the finish tone and grain direction have to be right or the repair looks like a patch. We bring samples and match against the existing cabinetry before any order is placed. On the countertop side, CWS kitchens in this area often paired with laminate or solid surface originally; if the surface has failed, we price Cambria and Silestone as replacement options because both hold up better in this climate than the original materials typically do.
Styles & brands we work with
Signs Your CWS Kitchen Remodeling Is Failing
- A drawer no longer soft-closes, or slams shut. The damper inside the glide has worn out. This is the most common CWS failure we see in West Palm Beach, and it usually starts with one drawer, then spreads as the same glide model ages across the kitchen.
- A cabinet door droops or won’t stay closed. The hinge cup has loosened or the hinge arm has bent. If you tighten the screws and it still droops, the hinge has failed internally and needs replacement, not adjustment.
- The countertop seam has opened or the edge is lifting. Florida humidity and daily cleaning wear the adhesive bond. If water gets into an open seam, it swells the substrate beneath a laminate top. That turns a $200 seam repair into a much larger surface replacement.
- The cabinet box has pulled away from the wall or the base is soft at the toe kick. This is water, not age. A past sink leak or years of mopping against the toe kick has compromised the board. We find this often behind dishwashers in older CWS installs.
- The backsplash grout is cracking or tiles are loose around the cooktop. Heat cycles and moisture have done their work. If the grout is cracked and the wall behind feels soft, you need more than a re-grout; you need the wet wall opened and fixed before new tile goes up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In West Palm Beach, full CWS kitchen remodels run $14,000 – $45,000. Smaller scoped jobs sit lower: cabinet installation alone runs $4,000 – $13,000, countertop installation $2,000 – $6,500, backsplash replacement $800 – $2,500, and an island addition $3,000 – $10,000. The range depends on material, cabinet count, whether we’re reusing the existing boxes or starting fresh, and what plumbing or electrical changes the job requires.
Every line item is on the written price before we start: labor, materials by brand and quantity, and a firm start and end window. We do not give an estimate that grows after the crew arrives. We pull permits where the jurisdiction requires them, and every completed project carries the 365-Day Done Right Promise. If something isn’t right after the job is complete, we make it right. Those are not marketing lines; they are Graham’s rules for every Elmstead Remodeling West Palm Beach job, including a photo of the clean-up before the crew leaves.
DIY or Call Us?
There are a few checks any homeowner can do safely: open every drawer and door and listen, feel the seam with a finger, look under the sink with a flashlight for water staining or soft board. Those observations help you describe the problem to us accurately and help us pull the right parts the first time.
Where DIY goes wrong on CWS kitchens is the cabinet structure itself. Once a box has pulled from the wall or the bottom board has water damage, the load path changes, and tightening fasteners into swollen or rotted board does real harm. The same is true for countertop removal: a failed seam often hides a swollen substrate, and the fix is not caulk, it’s uncovering the board, drying or replacing it, and resetting the surface. We carry the common CWS-spec drawer glides, hinge plates, and matched finishes on the truck, so most single-part fixes are done in one visit. Call us at (728) 203-3270 and describe what you’re seeing. We will tell you whether it’s a truck-stock part or a matched-order item and what the written price looks like either way.
FAQs
The cabinet boxes typically last 15 – 25 years in this climate, but the hardware – hinges, glides, dampers – wears out every 7 – 12 years under daily use. Countertops and backsplashes have their own lives: laminate and grouted tile fail sooner in Florida humidity than solid surface or quartz do, which is why we price Cambria and Silestone as long-term replacements.
A glide or hinge can rarely be repaired; they are built as sealed units and replacement is the honest fix. A cabinet box or door can often be repaired if the damage is caught before water has spread. We will tell you which path makes sense for your kitchen, and the written price covers exactly the work we agree on. Call (728) 203-3270 and we’ll walk through it.
Most single-part replacements – a drawer glide, a hinge set, a door adjustment – are done in one visit, usually an hour or two on site. A countertop seam repair may take half a day because the adhesive needs a clean, dry bond line to cure. A full CWS kitchen remodel in West Palm Beach typically runs 4 – 10 weeks depending on scope and material lead times.
We stock the common CWS-spec drawer glides, soft-close hinges, and cabinet hardware on the truck. Matched doors, drawer fronts, and custom panels are ordered per job from the cabinet shop to match the existing finish and grain. We carry KraftMaid, Cambria, and Silestone as the named-brand lines we specify when a larger replacement makes sense.
Written by Graham Stein, Owner, Elmstead Remodeling West Palm Beach at Elmstead Remodeling West Palm Beach, serving West Palm Beach and nearby areas.
