Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Windows & Doors: The West Palm Beach Owner’s Guide
If you have a Boral window or door with a failed sash, worn weather stripping, a cracked glass unit, or a lock that no longer catches, we can match the part, price it in writing, and install it the same visit in most cases. Typical Boral window and door part repairs in West Palm Beach run between $400 and $1,800 depending on the component, while full window or door replacements on Boral systems land in the $4,500 to $15,000 range. Most owners discover the failure the way our crews do: a window that suddenly takes two hands to lift, a door that drags on the jamb after a humid stretch, or condensation fogging between panes that won’t wipe away.
We’re an independent remodeling contractor in West Palm Beach, not a Boral dealer or affiliate, and we keep a running stock of the Boral-compatible components that fail most often in South Florida’s salt air and summer heat. That means less waiting on a freight shipment while a window won’t close.
Key takeaways:
- We price every Boral repair in writing before work starts, parts and labor separated.
- Most Boral window and door repairs take under two hours once the part is confirmed.
- We carry common Boral glazing beads, balance systems, rollers, and weather seals on the truck.
- Every repair is covered by the 365-Day Done Right Promise: if it isn’t right, we make it right.
Which Boral Models This Applies To
Boral manufactured windows and doors under several lines over the years, including the Classic, Builder’s, and custom architectural series, with both aluminum-clad and all-aluminum frames showing up throughout West Palm Beach. The part you need depends on which series the original installer used, and that’s where we see compatibility problems. A sash balance from a Builder’s series window does not always seat correctly in a Classic frame, even when the visible dimensions match. We identify the series from the label etchings on the spacer bar or the frame’s lower rail, then confirm against the original cut sheet before ordering anything.
For most Boral parts, the choice is between OEM components and quality aftermarket equivalents from manufacturers like Truth Hardware, Caldwell, and Prime-Line. The honest trade-off: OEM parts carry the original manufacturer’s spec and are usually warrantied, but lead times from Boral’s successor supply chain can stretch to three or four weeks. Aftermarket equivalents from reputable brands often arrive within days and perform identically in our experience. We walk through both prices in writing and let the homeowner decide.
Styles & brands we work with
Signs Your Boral Windows & Doors Is Failing
- The window won’t stay up or takes real effort to lift. This is usually a failed balance system. The spring or block-and-tackle mechanism inside the jamb has worn out, and the window’s full weight is now resting on the operator. Replacing one balance often means doing both sides so the window travels evenly.
- Condensation between the panes that won’t wipe away. The insulated glass unit’s seal has failed. Once the argon or krypton fill escapes and moist Florida air gets inside, the glass fogs permanently. The fix is a new IGU cut to the opening, not a seal repair.
- A door that drags or scrapes against the jamb on one side. In West Palm Beach, this is often the hinge or the frame settling rather than the door itself warping. Aluminum frames expand in direct sun and contract at night. We check hinge screws, the sill track, and the frame’s squareness before assuming the door needs replacing.
- The lock or multi-point latch no longer lines up with the strike plate. Older Boral doors used a multi-point locking system that can slip out of alignment over time. Sometimes it’s a simple adjustment; sometimes the gearbox inside the lock has stripped and needs a replacement cassette.
- You can feel air moving around a closed window or door. The weather stripping has flattened or broken down. In a coastal climate like West Palm Beach, salt air accelerates this. New compressed foam or EPDM bulb seals usually fix the draft the same day.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Boral part repairs in West Palm Beach run from $400 to $1,800 installed for most components. A single sash balance replacement typically runs $400 to $600. A new insulated glass unit for a Boral window runs $500 to $1,200 depending on size and low-E coating. A multi-point lock replacement runs $500 to $900. Full Boral window or door replacement is a different scope: $4,500 to $15,000 for most homes, comparable to what we quote for impact window installation at $8,000 to $25,000 when hurricane protection is part of the scope.
What’s included in every repair: the part itself at our cost plus the labor to install it, a written line-item price before work starts, shoe covers and drop cloths on every visit, a photo of the clean-up before the crew leaves, and the 365-Day Done Right Promise on the work. No change orders, no surprises after the crew arrives. Graham Stein walks every job site himself before any work begins.
DIY or Call Us?
There are safe checks you can do yourself: note the window’s brand etchings, open and close it a few times to see where it binds, and check whether the weather stripping looks flattened or missing. You can photograph the label so we can confirm the series before the first truck rolls. What we’d ask you not to tackle alone is replacing a sash balance under tension. Balances hold stored spring force, and removing one incorrectly can send the window or the mechanism flying. The same caution applies to multi-point door locks; the gearboxes sit inside a mortised cut, and forcing them out without the right extraction tool damages the door slab. If the part is under tension or inside a cut, let a trained crew handle it.
Call (728) 203-3270 and we’ll walk through what you’re seeing. If it’s something we can identify over the phone, we’ll tell you honestly.
FAQs
Boral aluminum windows and doors in West Palm Beach typically last 20 to 30 years for the frame, with components like balances, weather stripping, and locks failing sooner due to salt air and humidity. We see original Boral installs from the late 1990s and early 2000s still in service around neighborhoods like Flamingo Park, but most have had at least one balance or seal replaced by now. Call (728) 203-3270 if you’d like us to look at what you have.
Minor issues like lock alignment and weather stripping can often be adjusted or re-seated without new parts, but failed balances, broken multi-point lock gearboxes, and fogged insulated glass units need replacement components, not repairs. We’ll tell you which category yours falls into before any money changes hands. A written price comes first, either way.
Once the correct part is in hand, most Boral window and door repairs take under two hours. Balances, weather seals, and lock cassettes are same-visit jobs. Custom-glass insulated units take longer only because the glass has to be cut and sealed. We give a firm window before the crew arrives and we work around nap schedules and pet routines where we can.
We carry common Boral glazing beads, balance systems, rollers, and weather seals on the truck, along with matching hardware from Truth Hardware, Caldwell, and Prime-Line. Specialty items like custom-sized insulated glass units are ordered to spec. We also keep parts for KraftMaid, Cambria, and Silestone systems. Call (728) 203-3270 and we’ll confirm what’s on the truck for your exact model before we schedule.
Put it in writing, then do exactly that. That’s how we handle every Boral window and door repair in West Palm Beach, and it starts with a phone call to (728) 203-3270.
Written by Graham Stein, Owner, Elmstead Remodeling West Palm Beach at Elmstead Remodeling West Palm Beach, serving West Palm Beach and nearby areas.
