Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The West Palm Beach Owner’s Guide
If you’re researching Schluter driveway and paver systems in West Palm Beach, the short answer is this: the drain, edge, and transition profiles Schluter makes for paver applications typically run $45 – $180 per linear foot installed, with full paver driveway work in West Palm Beach ranging from $7,000 – $18,000 depending on square footage and substrate condition. We stock the common Schluter profiles on the truck and can match a failed section same-day if it’s a standard series. Where owners usually discover the problem is at the driveway edge, where a paver has shifted off a corroded edge profile, or where a Schluter drain channel has pulled away from the slab after a heavy South Florida rain.
What you’ll find below is the specific compatibility information, the failure patterns we see in West Palm Beach, honest pricing, and what’s safe to touch versus what needs a trained crew. We’re an independent contractor, not affiliated with Schluter, but we install and replace their products regularly because the named-brand warranty travels with the finished work.
Which Schluter Models This Applies To
Schluter’s driveway and paver line breaks into three families: the TROBA drainage and uncoupling sheets, the BARA edge profiles, and the SCHIENE and RONDEC transition profiles that finish the edge where pavers meet a slab or step. The compatibility gotcha: BARA profiles come in heights from 3/8″ to 5/8″, and the height has to match the paver thickness plus the setting bed. A 2″ paver on a 1″ sand bed needs a taller profile than a 1.5″ paver on a half-inch mud bed. We measure the paver and bed depth on site before ordering anything.
OEM versus aftermarket: for Schluter, we recommend staying with OEM profiles if the rest of the run is intact. The aluminum alloy and the drainage slot spacing on the TROBA line are specific, and an aftermarket edge often sits a few thousandths off, which reads as a lip after the first rain. If we’re replacing an entire edge run because the original series was discontinued, we’ll quote a current-series equivalent and tell you what changes before we touch anything. Graham Stein checks the label codes himself before we order, because a discontinued color code is the most common reason a repair gets delayed.
Styles & brands we work with
Signs Your Schluter Driveway & Pavers Is Failing
- Pavers at the edge are tilting or sinking. The BARA edge profile has lost its anchor to the setting bed, usually because the substrate washed out beneath it during a storm. South Florida’s sandy soil doesn’t hold profiles the way clay does up north.
- The drain channel pulls away from the slab. Thermal expansion in West Palm Beach’s heat-and-rain cycles works the TROBA channel loose over time. The seal between channel and concrete fails first, then the channel itself starts to flex.
- Visible corrosion on aluminum profiles. Salt air from the Atlantic accelerates oxidation on exposed aluminum. You’ll see white pitting first, then flaking at the screw holes.
- Water pooling against the garage slab after rain. That’s usually a TROBA drainage sheet that’s compacted or clogged with sand fines, so water backs up instead of moving through the channels.
- A metallic rattle under foot traffic. A profile that’s broken free from its setting bed will vibrate against the slab. It sounds like a loose gutter bracket, and it’s the earliest warning you’ll get.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Schluter edge or drain profile replacement in West Palm Beach, you’re looking at $45 – $180 per linear foot installed, which includes removing the affected pavers, repairing the setting bed, installing the new profile, and re-setting the pavers. A short 10-foot edge run typically lands around $450 – $1,200 total. A full paver driveway replacement using Schluter drainage and edge systems runs $7,000 – $18,000 in West Palm Beach, depending on square footage, excavation depth, and whether we’re reusing the existing base or rebuilding it.
The written price you get from us before any work starts includes the Schluter part by series and quantity, the setting bed material, labor, and haul-away of the failed section. If we find something under the pavers that changes the scope, we stop, call you, and put the revised price in writing before we continue. No crew arrives and discovers a mystery that grows the invoice. The replacement is covered by our 365-Day Done Right Promise: if it’s not right after the job is done, we make it right.
DIY or Call Us?
The safe DIY check: take a photo of the failed area, note whether any pavers are cracked or shifted, and measure the exposed edge height if you can do it without prying anything up. That information helps us quote accurately over the phone. What we’d stop you from doing yourself: pulling pavers to inspect the profile. The setting bed gives way without warning once a section is unconfined, and a 40-pound paver dropping on a hand or foot is a real injury. Schluter profiles also sit under tension from the paver weight, and releasing that tension wrong sends the edge flying. Call us at (728) 203-3270, send the photos, and let Graham walk the site before anything gets touched.
FAQs
OEM Schluter aluminum profiles typically last 15 – 25 years in West Palm Beach, with the salt-air exposure cutting that to the lower end near the water. The failure you’ll see first is corrosion at the screw holes, not the profile bending.
Yes, if the profile is intact and the problem is washed-out setting bed material, we can re-set the profile and pavers without replacing the part. If the profile itself shows corrosion or has pulled loose from its anchors, replacement is the honest fix. Call us at (728) 203-3270 and we’ll tell you which one you’re looking at before we schedule anything.
A typical edge or drain replacement takes one day for a single run, including re-setting the pavers and clean-up. A full driveway with new Schluter drainage runs 5 – 10 working days in West Palm Beach, weather depending.
We stock the common BARA and TROBA heights on the truck and can match a standard failed section same-day in West Palm Beach. Uncommon series or color codes get ordered direct, which typically adds 3 – 5 business days. We’ll tell you which situation you’re in before you agree to anything.
If your Schluter driveway edge, drain, or paver transition has failed, call (728) 203-3270 for a free estimate. We’ll walk the site, name the part, and put the price in writing before any work starts. Put it in writing, then do exactly that.
Written by Graham Stein, Owner, Elmstead Remodeling West Palm Beach at Elmstead Remodeling West Palm Beach, serving West Palm Beach and nearby areas.
